16.8V Traxxas E-Maxx Monster Truck.
(Click on Image to enlarge)
List Price: $369.99
This is the 1/10 scale electric powered, radio controlled, ready-to-run
16.8V Traxxas E-Maxx Monster Truck.
Equipped with dual brushed motors but all components are
built for brushless power-no driveline upgrades needed.
FEATURES: Chassis: 0.08" (2mm) thick composite with snap lock battery hold
downs and scaleable battery components to fit a variety of stick,
or side-by-side packs
Drive: Four wheel shaft drive with Revo spec sealed large diameter
outer and center driveshafts
Motors: 16.8 volt Titan 550 size fan cooled dual brushed motors
Radio: Traxxas TQ 2-channel 27MHz AM pistol grip with two
waterproof high-torque steering servos and sealed receiver box for
running in wet conditions, transmitter does not have charge jack
Electronic Speed Control: Traxxas EVX-2 forward and reverse ESC with
three programmable driver profiles and training mode
Ball Bearings: Full set, rubber sealed
Shocks: Eight oil-filled, composite bodied with red springs, rubber
pressure bladders ans double O-ring seals
Gearbox: Sealed
Differentials: Revo spec with X-ring seals to keep oil in and dirt
out, bevel gear design
Slipper Clutch: Traxxas's patent pending Torque-Control slipper
clutch
Transmission: Single-speed (two speed optional)
Tires: Treaded soft compound Maxx, 5.9" (149mm) outer diameter, 3.25"
(82mm) width
Wheels: 3.8" (96mm) diameter chrome 10 spoke (spokes are in groups
of two) 2.7" (70mm) width, 14mm hex
Bumpers: Plastic front and rear with kickups
Suspension: Adjustable Revo Spec sealed pivot balls
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
Steering: Heavy duty dual servo bell-crank type with ball bearings
INCLUDES: 16.8V Traxxas E-Maxx Monster Truck, oil-filled shocks, two motors,
electronic speed control, painted body, tires, foam inserts,
3-ch radio, two steering servos, wheels, instructions, decals,
tools and foam battery spacers
REQUIRES: Radio Batteries: Eight AA
Batteries: 6-or 7-cell stick packs with Traxxas high current
connector OR Female Connector to Molex Male Connector, TRAC3062 if
using battery with Standard connector (most chargers will still
require this adapter)
Battery Charger: Timed or peak type for selected batteries
Misc. Items: Building and track equipment
SPECS: VEHICLE-
Length: 20.4" (518mm)
Width: 16.5" (419mm)
Height: 9.8" (248mm)
Weight: 7.2 lbs (3290g) approx. without batteries
Wheelbase: 13.2" (335mm)
Front Tread: 12.9" (329mm)
Rear Tread: 13.0" (331mm) side-to-side at wheel centers
Front Track: 16.4" (417mm)
Rear Track: 16.5" (419mm) side to side at outer edges of wheels
Ground Clearance: 2.6" (65mm)
BODY-
Length: 19.4" (493mm)
Width: 6.9" (175mm) at rear wheels (widest point)
6.4" (164mm) behind from wheels (thinnest point)
Height: 5.3" (135mm)
COMMENTS: Do NOT use LiPo batteries with the stock motor setup in this vehicle.
The EVX-2 speed control is not equipped with low voltage detection.
For single motor installations, use the Single Motor Plate (TRAC3999)
and the Gear Cover (TRAC3977).
For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
2 6x12mm Fr Axle Carrier 1 DTXC1569
2 12x18mm Fr Axle Carrier 1 DTXC1597
2 6x12mm R Axle Carrier 1 DTXC1569
2 12x18mm R Axle Carrier 1 DTXC1597
2 5x11mm Steering Bellcranks 1 DTXC1547
3 5x11mm Fr Diff 1 DTXC1547
2 5x11mm Idler gear 1 DTXC1547
2 6x12mm Output Shaft 1 DTXC1569
1 10x15mm R Diff 1 DTXC1595
1 8x16mm R Diff 1 DTXC1585
2 6x12mm R Diff 1 DTXC1569
The E-Maxx is available in the following radio channels and colors;
TRAC92A2 A2 Red
TRAC92A4 A4 Black
TRAC92A5 A5 White
TRAC92A6 A6 Blue
jxs 10/22/07
ir/jxs
ACCESSORIES
THIS IS THE 1/10 SCALE ELECTRIC POWERED RTR, 16.8V TRAXXAS E-MAXX MONSTER TRUCK
FEATURES: DUAL 550 BRUSHED MOTORS, SEALED PIVOT BALLS, RADIO BOX, DIFFS &
DRIVESHAFTS, 3-CH RADIO W/2 WATERPROOF STEERING SERVOS, 8 OIL FILLED SHOCKS,
PAINTED BODY, DECALS, TOOLS, QUICK RELEASE BATTERY HOLD DOWNS,
REQUIRES: TWO 6-OR 7-CELL BATTERIES W/HIGH CURRENT PLUG, CHARGER, 8 AA CELLS